na3D
Producer website: www.na3D.cz
-
Closed belt GT2 GT2-6
GT2 belt loop - width 6mm in length of your choice. The specified length indicates the circumference of the belt and is in millimeters. (The product can be ordered 1 piece at a time, the photo is only illustrative.)
In stock <10pcs
from 1,72 €
-
Teflon tube 4/2, 3/2, 4/3, 6/4 PTFE tube
Teflon tube for hotend or for bowden. 1pc = 10cm
In stock <10pcs
from 0,18 €
-
Hardened MK8 nozzle - Czech Product
Hardened steel nozzle produced by our company in the Czech Republic. M6 threaded nozzle - the most widespread thread in 3D printers, can be used in several types, the shape corresponds to the most printers of Creality, Ender, and Anet. Made in the Czech Republic.
In stock <10pcs
3,48 €
-
Hardened Volcano nozzle - Czech product
Hardened steel nozzle produced by our company in the Czech Republic. M6 threaded nozzle - the most widespread thread in 3D printers, can be used in several types of printers. Made in the Czech Republic.
In stock <10pcs
4,18 €
-
Set of modeling tools - spatula
Model stainless steel spatula to remove prints.
In stock <10pcs (1 pcs)
7 €
-
Flexible clutch - clamping, firm, flexible clutch
The flexible clutch is used to transmit torque between the rod and the engine. The flexible clutch does not destroy the engine. It helps to easily service interventions. It brings accuracy to assembling your devices. (The product can be ordered after 1 piece, the photo is only illustrative.)
In stock <10pcs
from 3,13 €
-
DUPONT cables
Extension cables 2 -pin, 3 -pin and 4 -pin available in two lengths. The cable is fitted with a dupont connector - female - female.
In stock <10pcs
1,37 €
-
A set of drills to clean the nozzles
The set contains 10 pieces of drills with a diameter of 0.2 mm or 0.4 mm used to clean the nozzles. When blocking the nozzle, heat it to about 200 ° C and then clean the clockwise with a gentle circular movements with a drill.
In stock <10pcs
8,05 €
-
Nozzles
Drills with a diameter of 0.2 mm / 0.25 mm / 0.3 mm / 0.35 mm / 0.4 mm / 0.45 mm / 0.5 mm used to clean the nozzles. When blocking the nozzle, heat it to about 200 ° C and then clean the clockwise with a gentle circular movements with a drill.
In stock <10pcs
0,67 €
-
USB/USB -B cable - 0.3m
Data connecting cable for connecting the printer to the USB port of the computer.
In stock <10pcs (3 pcs)
1,37 €
-
Set 10 DLAT - Wooden Handle
Set of model chips suitable for cleaning the model from support or possible uneven prints.
In stock <10pcs (4 pcs)
7 €
-
Fan Extender
Extension for RAMPS 1.4 to connect additional fans. Use, for example, for cooling chambers, printing, hotend, etc. The module requires a FW update.
In stock <10pcs (2 pcs)
7 €
-
LM12UU linear bearing
Linear bearing with 4 rows of balls suitable for bars with a diameter of 12 mm. (The product can be ordered after 1 piece, the photo is only illustrative.)
In stock <10pcs (2 pcs)
1,72 €
-
Sensor for calibration of Bltouch pad original Antclabs
Original BLTOUCH V3.1 sensor for automatic calibration of the printing area.
In stock <10pcs (1 pcs)
49,20 €
-
Tweezers - straight
The tweezers are suitable for removing the filament from the hot nozzle, or pulling supports from small spaces.
In stock <10pcs (2 pcs)
1,37 €